Viewing Single Post From: Storm Commando CRL Specs Needed

Viewing Single Post From: Storm Commando CRL Specs Needed
COS_Vader	Sep 9 2008, 08:12 PM
Detachment Leader Posts: 1,607 Group: Supporter Member #1 Joined: June 1, 2005	Storm Commando/Imperial Commando/Shadow Scout CRL BASE STANDARDS - Black version of Biker Scout (Same as BSN standards, but black armor) - Gloss/Semi-Gloss/Weathered Black Biker Scout helmet (Don Post/Rubies repainted or fan-made replica acceptable) The following modifications are required for the DP/Rubies helmet: * Remove the logo on the back neck * Repaint bucket gloss black * Replace lens (green/smoke/black/mirrored - You MUST NOT be able to see your eyes when the helmet is on) * Slim facemask if it's flared * Replace inaccurate "fish hook" * Replace bolts on visor/bucket * Replace aerator - Black matte textile long sleeve coveralls or flight suit. - Black textile Stormtrooper-style neck seal (You must never be able to see your neck) - Black leather or vinyl textureless gauntlet style motorcycle gloves. No extra straps, buckles, or ornamental stitching. Ribbing over knuckles should be present. - Black, non-shiny textile cummerbund with two standard Imperial pouches. - Black textureless or near-textureless vinyl/leather calf-high laceless boots. Wrap over bridge of foot must be present. Soles of boot must have black tread. - Black gloss/semi-gloss/weathered ABS or fiberglass chest armor. Gray/Dark Gray rectangular mark on left chest must be present. - Black gloss/semi-gloss/weathered back plate with tank. Tank must have pinstripe deco and anywhere from 4-6 "rank stripes" on right side of tank. Black tank topper must be present, but the red square "button" is optional. No permanent flashing lights or LED's are acceptable anywhere on the costume. - Black gloss/semi-gloss/weathered ABS or fiberglass shoulder bells, bicep armor, and elbow armor. Bicep armor must have black t-bits. - Black gloss/semi-gloss/weathered belt. 2" webbing belt with buckle and 4 utility case combination attached to the front. Thermal detonator box using gray hosing is attached at the rear of the belt. No permanent flashing lights, or colored marking other than black bits are acceptable. - Black gloss/semi-gloss/weathered ABS or fiberglass knee armor. - Black gloss/semi-gloss/weathered ABS or fiberglass boot holster fastened to boots with either Velcro or rivets. Strap attachment is NOT acceptable. - Boot holster and Holdout blaster. - Dirty modifications are allowed (Weathering) Optional (accepted, but not required) - DLT20a sniper rifle - Concept Scout Rifle - MG-34 Version 2 (elite) -Black Biker Scout ABS or fiberglass upper torso armor, back armor, belt, backpack, shoulder bells, knees and helmet. -Either 1 or 2 piece black textile undersuit. Underarmor (with logos hidden) or diving suits are common -Black gloves with minimal stitching. Gauntlet style is acceptable but must be tucked into forearm armor. Stormtrooper gloves are also acceptable. -Smooth black boots. They should have no ornamental stitching or other adornment of any kind unless specified. If taller than ankle height they must be tucked under shin armor. No laces, buckles, Velcro, or any kind of securing device may be visible. -Black textile Biker Scout cummerbund with pouches. -Smooth black ABS or fiberglass forearm armor -Smooth cod armor that curves inward as it goes down and does not extend horizontally past the groin. It should reach from the utility belt to the point where the pant legs meet. Or a segment of smooth armor covering the entire pelvic region. -Bicep armor should be either standard black stormtrooper style or biker scout style. -Either a neckseal (ribbed or smooth) or a black balaclava -Black ABS/Fiberglass Stormtrooper-style thigh armor Approved Options -Red opaque or reflective helmet lens (You must not be able to see your eyes when helmet is on) -2 red bandoliers crossing in the front and back. These should have hard ammo packs and look much like Chewbacca’s but with electronic portions near the buckles (see picture) -red buckle on belt (I took these from a storm commando in one of the comics that’s been posted for reference a couple of times. I’m not sure if this is what’s meant by “approved options” or if it should even be approved but I figured I’d post it A Storm Commando Should Have (recommended but not required) -Black Stormtrooper style handplates -A Biker Scout sidearm -Black shin armor resembling that worn by Jango Fett -All hard armor should be glossy to represent “reflec coating”. This can be done with gloss clear coat, the use of abs plastic, or any other way that produces the desired result A Storm Commando may have (accepted but not required) -A seam running along the inside of the forearm armor with a knob resembling a computer key near the inside of the elbow -Black thigh armor resembling that worn by Jango Fett which would only cover the front half of the leg. It would be attached with black elastic/fabric/leather straps running around the back Discuss... Edited by COS_Vader, Sep 9 2008, 08:21 PM.


Storm Commando CRL Specs Needed · Storm Commando